diff options
Diffstat (limited to 'sys-cluster/openib-osm/files/opensm.conf')
-rw-r--r-- | sys-cluster/openib-osm/files/opensm.conf | 141 |
1 files changed, 141 insertions, 0 deletions
diff --git a/sys-cluster/openib-osm/files/opensm.conf b/sys-cluster/openib-osm/files/opensm.conf new file mode 100644 index 000000000..58880400d --- /dev/null +++ b/sys-cluster/openib-osm/files/opensm.conf @@ -0,0 +1,141 @@ +# DEBUG mode +# This option specifies a debug option. +# These options are not normally needed. +# The number following -d selects the debug +# option to enable as follows: +# OPT Description +# --- ----------------- +# 0 - Ignore other SM nodes. +# 1 - Force single threaded dispatching. +# 2 - Force log flushing after each log message. +# 3 - Disable multicast support. +# 4 - Put OpenSM in memory tracking mode. +# 10.. Put OpenSM in testability mode. +# none, no debug options are enabled. +DEBUG=none + +# LMC +# This option specifies the subnet's LMC value. +# The number of LIDs assigned to each port is 2^LMC. +# The LMC value must be in the range 0-7. +# LMC values > 0 allow multiple paths between ports. +# LMC values > 0 should only be used if the subnet +# topology actually provides multiple paths between +# ports, i.e. multiple interconnects between switches. +# OpenSM defaults to LMC = 0, which allows +# one path between any two ports. +LMC=0 + +# MAXSMPS +# This option specifies the number of VL15 SMP MADs +# allowed on the wire at any one time. +# Specifying -maxsmps 0 allows unlimited outstanding SMPs. +# Without -maxsmps, OpenSM defaults to a maximum of +# one outstanding SMP. +MAXSMPS=0 + +# REASSIGN_LIDS +# This option causes OpenSM to reassign LIDs to all +# end nodes. Specifying "REASSIGN_LIDS=yes" on a running subnet +# may disrupt subnet traffic. +# With "REASSIGN_LIDS=no", OpenSM attempts to preserve existing +# LID assignments resolving multiple use of same LID. +REASSIGN_LIDS="no" + +# SWEEP +# This option specifies the number of seconds between +# subnet sweeps. Specifying SWEEP=0 disables sweeping. +# OpenSM defaults to a sweep interval of 10 seconds. +SWEEP=10 + +# TIMEOUT +# This option specifies the time in milliseconds +# used for transaction timeouts. +# Specifying -t 0 disables timeouts. +# Without -t, OpenSM defaults to a timeout value of +# 100 milliseconds. +TIMEOUT=200 + + +# OSM_LOG +# This option defines the log to be the given file. +# By default the log goes to /tmp/osm.log. +# For the log to go to standard output use OSM_LOG=stdout. +OSM_LOG=/tmp/osm.log + +# VERBOSE +# This option increases the log verbosity level. +# The "-v" option may be specified multiple times +# to further increase the verbosity level. +# "-V" option sets the maximum verbosity level and +# forces log flushing. +# The "-V" is equivalent to "-vf 0xFF -d 2". +VERBOSE="none" + +# UPDN +# This option activate UPDN algorithm instead of Min Hop +# algorithm (default). +# To switch on UPDN algorithm set UPDN="on" +UPDN="off" + + +# GUID_FILE +# This option only allowed when UPDN algorithm is activated +# It specifies the guid list file from which to fetch the guid list +# The file contain in each line only one valid guid +GUID_FILE="none" + +# This option specifies the local port GUID value +# with which OpenSM should bind. OpenSM may be +# bound to 1 port at a time. +# If GUID given is 0, opensmd use PORT_NUM parameter. +# Without -g (GUID="none"), OpenSM trys to use the default port. +GUID=0 + +# OSM_HOSTS +# The list of all SM's IP addresses in InfiniBand subnet +# Used to handover mechanism +OSM_HOSTS="" + +# OSM_CACHE_DIR +OSM_CACHE_DIR=/var/cache/osm + +# CACHE_OPTIONS +# Cache the given command line options into the file +# /var/cache/osm/opensm.opts for use next invocation +# The cache directory can be changed by the environment +# variable OSM_CACHE_DIR +# Set to '--cache-options' or '-c' in order to enable +CACHE_OPTIONS="none" + +# HONORE_GUID2LID +# This option forces OpenSM to honor the guid2lid file, +# when it comes out of Standby state, if such file exists +# under OSM_CACHE_DIR, and is valid. +# Set to '--honor_guid2lid' or '-x' to enable. +# By default this is FALSE. Will be set automatically to '--honor_guid2lid' +# if OSM_HOSTS includes list of more then one IP addresses. +HONORE_GUID2LID="none" + +# RCP +# This option osed by SLDD daemon for handover mechanism +# to copy local cache file to remote computer +RCP=/usr/bin/scp + +# RSH +# This option osed by SLDD daemon for handover mechanism +# to execute commands on remote computer +RSH=/usr/bin/ssh + +# RESCAN_TIME +# This option osed by SLDD daemon for handover mechanism +# Time between sweep of sldd daemon in seconds +RESCAN_TIME=60 + +# PORT_NUM +# This option defines HCA's port number which OpenSM should bind +PORT_NUM=1 + +# ONBOOT +# To start OpenSM automatically set ONBOOT=yes +ONBOOT=no |