diff options
Diffstat (limited to 'sys-fs/lvm2/files/lvm.rc-2.02.166-r2')
| -rw-r--r-- | sys-fs/lvm2/files/lvm.rc-2.02.166-r2 | 145 |
1 files changed, 0 insertions, 145 deletions
diff --git a/sys-fs/lvm2/files/lvm.rc-2.02.166-r2 b/sys-fs/lvm2/files/lvm.rc-2.02.166-r2 deleted file mode 100644 index 11329bbeaf33..000000000000 --- a/sys-fs/lvm2/files/lvm.rc-2.02.166-r2 +++ /dev/null @@ -1,145 +0,0 @@ -#!/sbin/openrc-run -# Copyright 1999-2017 Gentoo Foundation -# Distributed under the terms of the GNU General Public License v2 - -_get_lvm_path() { - local lvm_path= - for lvm_path in /bin/lvm /sbin/lvm ; do - [ -x "$lvm_path" ] && break - done - echo "${lvm_path}" -} - -_need_lvmetad() -{ - local lvm_path="$(_get_lvm_path)" - [ ! -x "${lvm_path}" ] && return 1 - ${lvm_path} dumpconfig global 2>/dev/null | grep -q 'use_lvmetad=1' -} - -_need_lvmlockd() -{ - local lvm_path="$(_get_lvm_path)" - [ ! -x "${lvm_path}" ] && return 1 - ${lvm_path} dumpconfig global 2>/dev/null | grep -q 'use_lvmlockd=1' -} -depend() { - before checkfs fsck - after modules device-mapper - # We may use lvmetad based on the configuration. If we added lvmetad - # support while lvm2 is running then we aren't dependent on it. For the - # more common case, if its disabled in the config we aren't dependent - # on it. - config /etc/lvm/lvm.conf - local _need= - if service_started; then - _need=$(service_get_value need) - else - if _need_lvmetad; then - _need="${_need} lvmetad" - fi - if _need_lvmlockd; then - _need="${_need} lvmlockd" - fi - fi - need sysfs ${_need} -} - -config='global { locking_dir = "/run/lock/lvm" }' - -dm_in_proc() { - local retval=0 - for x in devices misc ; do - grep -qs 'device-mapper' /proc/${x} - retval=$((${retval} + $?)) - done - return ${retval} -} - -start() { - # LVM support for /usr, /home, /opt .... - # This should be done *before* checking local - # volumes, or they never get checked. - - # NOTE: Add needed modules for LVM or RAID, etc - # to /etc/modules.autoload if needed - lvm_path="$(_get_lvm_path)" - for lvm_path in /bin/lvm /sbin/lvm ; do - [ -x "$lvm_path" ] && break - done - if [ ! -x "$lvm_path" ]; then - eerror "Cannot find lvm binary in /sbin or /bin!" - return 1 - fi - if [ -z "${CDBOOT}" ] ; then - if [ -e /proc/modules ] && ! dm_in_proc ; then - modprobe dm-mod 2>/dev/null - fi - if [ -d /proc/lvm ] || dm_in_proc ; then - ebegin "Setting up the Logical Volume Manager" - #still echo stderr for debugging - lvm_commands="#! ${lvm_path} --config '${config}'\n" - # Extra PV find pass because some devices might not have been available until very recently - lvm_commands="${lvm_commands}pvscan\n" - # Now make the nodes - lvm_commands="${lvm_commands}vgscan --mknodes\n" - # And turn them on! - lvm_commands="${lvm_commands}vgchange --sysinit -a ly\n" - if _need_lvmlockd; then - # Start lockd VGs as required - lvm_commands="${lvm_commands}vgchange --lock-start --lock-opt auto\n" - fi - # Order of this is important, have to work around dash and LVM readline - printf "%b\n" "${lvm_commands}" | $lvm_path /proc/self/fd/0 --config "${config}" >/dev/null - eend $? "Failed to setup the LVM" - fi - fi -} - -start_post() -{ - # Save if we needed lvmetad - if _need_lvmetad; then - service_set_value need lvmetad - fi -} - -stop() { - for lvm_path in /bin/lvm /sbin/lvm ; do - [ -x "$lvm_path" ] && break - done - if [ ! -x "$lvm_path" ]; then - eerror "Cannot find lvm binary in /sbin or /bin!" - return 1 - fi -# Stop LVM2 -if [ -x /sbin/vgs ] && \ - [ -x /sbin/vgchange ] && \ - [ -x /sbin/lvchange ] && \ - [ -f /etc/lvmtab -o -d /etc/lvm ] && \ - [ -d /proc/lvm -o "`grep device-mapper /proc/misc 2>/dev/null`" ] -then - einfo "Shutting down the Logical Volume Manager" - - VGS=$($lvm_path vgs --config "${config}" -o vg_name --noheadings --nosuffix --rows 2> /dev/null) - - if [ "$VGS" ] - then - ebegin " Shutting Down LVs & VGs" - #still echo stderr for debugging - lvm_commands="#! ${lvm_path} --config '${config}'\n" - # Extra PV find pass because some devices might not have been available until very recently - lvm_commands="${lvm_commands}lvchange --sysinit -a ln ${VGS}\n" - # Now make the nodes - lvm_commands="${lvm_commands}vgchange --sysinit -a ln ${VGS}\n" - # Order of this is important, have to work around dash and LVM readline - printf "%b\n" "${lvm_commands}" | $lvm_path /proc/self/fd/0 --config "${config}" >/dev/null - eend $? "Failed (possibly some LVs still needed for /usr or root)" - fi - - einfo "Finished shutting down the Logical Volume Manager" - return 0 -fi -} - -# vim:ts=4 |